• When calibrating the no-load tester, TK6800 can switch the output transformer rated voltage or 50%~100% rated current, adjust the power output, realize the simulation of no-load and load loss, and calibrate the no-load tester.

• During the load test, the short-circuit impedance value can also be obtained at the same time to complete the calibration of the short-circuit impedance tester. Parameters can be used for transformer capacity calculations.

• When calibrating the capacity tester, TK6800 selects the corresponding gear according to the resistance value obtained by the short-circuit impedance test. Set the voltage output according to the calibration coefficient and measure the tester output current value. Calculate and determine the transformer capacity value through the obtained short-circuit impedance voltage and actual short-circuit impedance value, and calibrate the capacity tester.

Number

Function

Wiring panel, including no-load loss, capacity and short circuit impedance test voltage / current wiring port;

Emergency stop button, emergency stop equipment when the equipment output is abnormal;

Power supply switch, equipment power supply switch

Connecting terminal: LAN interface and RS232 interface for communication with computer;

The tested platform for placing the inspected equipment

Control the flat plate, display and operate the equipment output test;

Host power supply

☆ Wiring Panel

Number

Function

No-load loss tester wiring terminal, including three-phase voltage / current output maximum of 864 V, 60 A.

Capacity tester terminal with three-phase voltage output 10 V and three-phase current measurement 10 A.

Terminal terminal of short-circuit impedance tester with maximum three-phase voltage output 864 V and AC current output maximum 60 A.

• TK6800 standard source output has high stability. It adopts the design principle of closed-loop negative feedback system, which can measure and adjust the output power value in real time, ensure the real-time stability of the output, and can perform high repeatability measurement for a long time. The typical stability of AC voltage/current output is 0.005%/min.

• TK6800 can directly set the calibration point of no-load loss or directly set the capacity value and short-circuit impedance value for testing, without the need for the user to set the voltage value and current value one by one after calculation.

Number

Function

Set the amplitude of the selected harmonic, either by setting the absolute value of the voltage or current harmonic, or by the base wave percentage.

Set the phase of the selected harmonic (relative to the base wave).

The instrument has the output function of the 2nd~21st harmonics. The embedded software is configured with the user custom "Harmonic parameter Settings" interface, and the user can set it according to the harmonics required by the test demand switch.

With the function of oscilloscope, it can observe the AC power waveform of each phase after loading the harmonic.

Channel selection, select the waveform of each phase voltage or current channel displayed.

Display the spectrum of each harmonic (Fundamental wave is 100%).

Warm-up time

20 Minutes

Temperature Performance

Operating temperature: 15°C~35°C

   Storage temperature: -20°C~50°C

Humidity Performance

Working Humidity: <80% @ 30°C, <70% @ 40°C, and <40% @ 50°C

   Storage humidity: (20%~80%) R·H, no condensation

Altitude

< 3000 m

Communication Interface

LAN 、RS232

Dimension

505 mm (W) × 700 mm (D) × 1200 mm (H)

1

Voltage Test Leads

1.5m / 2.1mm2/ Φ 4- Φ 4-Socket

Red 1

Green 1

Yellow 1

Black 3

Standard accessories

2

Test Leads

1.5m / 8mm2/ Φ 4- Φ 4-Socket

Red 1

Green 1

Yellow 1

Black 3

Standard accessories

3

Tablet

With the wireless WiFi module, equipped with the APP operation software

1

Standard accessories

4

Network Cable

1 Meters

1

Standard accessories

5

Network Cable

5 Meters

1

Standard accessories

6

Power Cable

AC 220V 、10A

1

Standard accessories

7

Glass fuse

F 8A 、250V

3

Standard accessories